-
KYB Toyota LiteAce Dual Wheel Rear Shock Absorber - KYB 343213
KYB Excel-G rear shock absorber for the Toyota LiteAce. Part number 343213. Gas charged, twin tube. Sold as one. New old stock. Never fitted. The box is scuffed and the label is scratched. The shock has not been touched. Fitment CM20 1.8 diesel van, 1983 to 1988, and KM20R petrol platform and chassis, 1979 to 1985. Dual rear wheel models only. If your LiteAce has single rear wheels this is not the right shock. Send us your rego and we will confirm before you buy. Fitting KYB recommend replacing shocks in pairs across the axle. This is one shock, so order two if you are doing both sides. Check the bushes and mounts while you are under there. Torque to spec.
$99.00
-
Mackay Toyota Hilux RZN149R 1997-2005 2.7 Engine Mount - Mackay A7596
Mackay engine mount for the Toyota Hilux RZN149R, 1997 to 2005, 2.7 litre 3RZ-FE. Part number A7596. Sold as one mount. New old stock. Never fitted. The bag has been on a shelf a while. The mount has not. Fitment Hilux RZN149R with the 2.7 litre 3RZ-FE petrol engine, 1997 to 2005, SR5 included. The Hilux uses more than one mount and Mackay do not state which position this one fills. Check it against the mount you are replacing, or send us your rego and we will confirm. Fitting Support the engine before you drop the old mount out. Check the other mounts while you are in there. They rarely fail alone. Torque to spec.
$69.00
-
Tenacity Toyota C-HR Rear Sway Bar Link - Tenacity 04-42571
Tenacity rear sway bar link for the Toyota C-HR. Part number 04-42571, also coded ATLTO1107. Sold as one link. New old stock. Never fitted. The box shows its age. The link does not. Fitment Suits the Toyota C-HR, as printed on the label. Send us your rego and we will confirm before you buy. Fitting A worn link is the usual cause of a knock or rattle over bumps. Do both sides while you are under there. One new link shows up the old one. Torque to spec.
$99.00
-
GMB Toyota Tie Rod End - GMB 0701-1250
GMB tie rod end, part number 0701-1250. Suits Toyota. GMB is an OE certified manufacturer. Sold as one. New old stock. Never fitted. The box has been on a shelf a while. The part has not. Fitment Suits selected Toyota models. Tie rod ends are matched by thread size, stud taper and length rather than by model name alone, and some vehicles take a different part on each side. Send us your rego and we will confirm the correct fitment before you order. Fitting Get a wheel alignment after fitting. Your steering will be out until you do. Torque the castle nut to spec and fit a new split pin. If one side is worn the other usually is too. A new joint shows up an old one.
$79.00
-
Tenacity Toyota Hilux LN65 Front Spring Shackle Bush - Tenacity 03-31183
Tenacity front spring shackle bush for the Toyota Hilux LN65. Part number 03-31183, also coded AAMTO1172. Sold as one bush. New old stock. Never fitted. The bag has been on a shelf a while. The bush has not. Fitment Suits the Toyota Hilux LN65, as printed on the label. Bushes are matched by inside diameter, outside diameter and length, so measure the one you are replacing or send us your rego and we will check it for you. Fitting Pressing bushes in and out needs the right tools. Get it done properly. Shackle bushes wear as a set. One new bush will not cure a knock if the rest are perished. Torque the shackle fixings at ride height, not with the axle hanging.
$24.90
-
Tenacity Toyota Yaris 2005-2013 Manual Engine Mount Stay - Tenacity 01-12579
Engine mount stay for the Toyota Yaris, 2005 to 2013. Tenacity 01-12579, also coded AWSTO1238. Sold as one.New old stock. Never fitted. The box shows its age. The stay does not.This is the torque rod, the one most people call the dog bone. It stops the engine rocking under load. A Yaris that clunks when you pull away or lift off has usually worn this out.FitmentToyota Yaris 2005 to 2013, as printed on the label. Send us your rego and we will confirm before you buy.Fitting Two bolts on most Yaris, so it is a short job. Look at the other mounts while you are in there. A worn stay usually comes with tired mounts. Torque both bolts to the Toyota figure. Best fitted by a qualified mechanic.
$79.00
-
Tenacity Toyota Corona 1.6 2.0 Strut Mount - Tenacity 02-20434
Tenacity strut mount for the Toyota Corona, 1.6 and 2.0. Part number 02-20434, also coded ASMTO1003. Sold as one mount. New old stock. Never fitted. The box shows its age. The mount does not. Fitment Toyota Corona 1.6 and 2.0, as printed on the label. No year range, side or axle is given, so check it against the one you are pulling out or send us your rego and we will confirm before you buy. Fitting Strut mounts need the spring compressed to change. Get it done properly. Do both sides. A new mount on one side shows up the old one. On a car this age check the bearing and the bump stop at the same time. Torque to spec.
$89.00
-
Tenacity Toyota Camry Celica 1985-1993 Left Engine Mount - Tenacity 01-12173
Left engine mount for the manual Toyota Camry and Celica. Tenacity 01-12173, also coded AWSTO1161. Sold as one.New old stock. Never fitted. The box shows the years on the shelf.FitmentLeft side, manual gearbox only. Australian catalogues list the equivalent left mount across the Camry SV21 and the Celica ST162. Both run the 2.0 litre 3S engine. The ST162 ran from 11/1985 to 10/1989 and the SV21 from 05/1987. Send us the rego and we will check yours.Fitting Take the weight off the engine and gearbox first. Look over the rest of the mounts while you are under it. Old rubber next to new rubber tells you what else needs doing. Torque the fixings to the Toyota figure. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Camry 1987-1993 Manual Rear Engine Mount - Tenacity 01-12200
Rear engine mount for the manual Toyota Camry SV2#. Tenacity 01-12200, also coded AWSTO1068. Sold as one.Never fitted. Old stock, box aged, mount untouched.FitmentRear position, manual gearbox only. SV2# is the V20 Camry. Australian catalogues list this mount for the SV21 and SV22 from 05/1987 to 01/1993. The automatic car takes 01-12199 instead. Send us the rego and we will check which you have.Fitting Hold the engine up before you start on the bolts. Give the rest of the mounts a look while it is apart. Side by side, a tired mount is easy to pick against a new one. Torque everything to the figure in the manual. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Front Engine Mount - Tenacity 01-12960
Front engine mount for Toyota, Tenacity 01-12960, code AWSTO1392. One per box.The box says Toyota and front, and names no model.New old stock. Never fitted. The box has the storage age.It is a solid rubber and steel mount. The box carries no hydraulic sticker.FitmentToyota, front position, as printed on the box. The model is not listed. Send us the rego and we will work out what it suits.Fitting Take the engine weight before you undo the old one. Give the others a look while it is apart. Bolts up to the figure in the manual. Best fitted by a qualified mechanic.
$79.00
-
Tenacity Toyota RAV4 XA10 1994-2000 Right Engine Mount - Tenacity 01-12152
Right engine mount for the first generation Toyota RAV4. Tenacity 01-12152, code AWSTO1141, one mount per box.New old stock. The bag has aged on the shelf. The mount has not been fitted.The box lists it for the RAV4 SXA1#, which covers the first RAV4 sold from 1994 to 2000.SXA1# is a wildcard code. It takes in SXA10 and SXA11, the four wheel drive cars, and SXA15 and SXA16, the front wheel drive ones. All of them run the 2.0 litre 3S-FE.FitmentToyota RAV4 SXA1#, right side, as printed on the label. Send your rego through and we will confirm.Fitting Take the engine weight before the old mount comes off. Check the rest of them at the same time. Bolts to the Toyota torque figure. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Camry 1987-1993 Auto Rear Engine Mount - Tenacity 01-12199
Rear engine mount for the automatic Toyota Camry SV2#. Tenacity 01-12199, also coded AWSTO1069. Sold as one.New old stock. Never fitted. The box has the storage age on it.FitmentRear position, automatic gearbox only. SV2# covers the V20 Camry. Australian catalogues list the rear automatic mount for the SV20, SV21 and SV22 built 1987 to 1993. The manual car takes 01-12200 instead. Send us the rego and we will match the gearbox.Fitting Support the engine before the mount is undone. Check the front mounts while you are in there. Next to a new one, a tired mount is obvious. Fixings to the Toyota torque figure. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Corolla ZRE172 2013-2019 Front Engine Mount - Tenacity 01-12562
Front engine mount for the Corolla ZRE172 sedan. Tenacity 01-12562, code AWSTO1334, one mount per box.The box lists the ZRE172, the 1.8 litre sedan built from 2013 to 2019.New old stock. Never fitted. The bag has the years on it.ZRE172 is the sedan with the 2ZR-FE engine. The hatch and the wagon carry different codes, so read the plate on your car.FitmentToyota Corolla ZRE172, front position, as printed on the label. Send us the rego and we will confirm the body.Fitting Support the engine before the old one comes off. Give the rest a look while you are there. Torque to the Toyota figure. Best fitted by a qualified mechanic.
$89.00
-
POK Toyota Echo Corolla 2001 on CV Joint Boot - POK PH98346
CV joint boot for the Toyota Echo and Corolla, 2001 on. POK PH98346, sub number PH98346C-L, made in Taiwan.New old stock. Never fitted. The bag shows how long it sat.This is the rubber boot by itself. The bag holds one boot, with no clamps or grease. The label does not say inner or outer, so check the one you are replacing.FitmentToyota Echo and Corolla, 2001 on, as printed on the label. Send us the rego and we will confirm the shaft.Fitting Old grease out of the joint first. Repack it with fresh CV grease. Fit new clamps rather than reusing the originals. Best fitted by a qualified mechanic.
$39.00
-
Tenacity Toyota Camry XV10 V6 1991-1996 Right Engine Mount - Tenacity 01-12091
Right engine mount for the V6 Camry XV10. Tenacity 01-12091, code AWSTO1018, one mount per box.Never fitted. Old stock, with storage age on the bag.The box lists the Camry #CV1#. That is a wildcard code covering VCV10 and MCV10. Those are the 3.0 litre V6 models in the XV10 range, 1991 to 1996. The four cylinder cars carry SXV10 and are not covered.FitmentToyota Camry #CV1#, right side, as printed on the label. Send us the rego and we will confirm the engine.Fitting Support the engine before this mount is undone. Check the rest while you have the weight off. Bolts up to the Toyota figure. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Harrier XU30 2006 on Engine Mount Stay - Tenacity 01-12561
Engine mount stay for the Toyota Harrier, 2006 on. Tenacity 01-12561, code AWSTO1293, one stay per box.New old stock. Never fitted. Years on the bag only.A stay is the arm that stops the engine rocking under load. Some catalogues call it a torque rod. It is not the same thing as a main engine mount.The 2006 date lines up with the mid life update to the XU30 Harrier, which ran from 2003 to 2013.FitmentToyota Harrier, 2006 on, as printed on the label. Send us the rego and we will pin the year down.Fitting Hold the engine steady before the stay comes off. Check the main mounts while you have it apart. Torque the bolts to the Toyota setting. Best fitted by a qualified mechanic.
$79.00
-
Tenacity Toyota Corolla 1.6 2008 on Front Engine Mount - Tenacity 01-12556
Front engine mount for the 1.6 Corolla ZRE120, automatic. Tenacity 01-12556, code AWSTO1237, one mount per box.New old stock. Never fitted. The bag shows where it has sat.Tenacity's catalogue lists AWSTO1237 as the front engine mount for the Corolla 1.6 from 2008, in the automatic version. It replaces Toyota part 12361-0T040, and the manual cars take a different mount.FitmentToyota Corolla 1.6, 2008 on, automatic, front position. The box gives the chassis code ZRE120. Send us the rego and we will confirm the transmission.Fitting Support the engine, then undo the old mount. Check the others on the car at the same time. Torque the bolts to the figure Toyota give. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Hilux Surf 4Runner Rear Engine Mount - Tenacity 01-12046
Rear engine mount for the Toyota Hilux Surf and 4Runner. Tenacity 01-12046, code AWSTO1368, one mount per box.Never fitted. Old stock, with the bag showing its years.The Surf and the 4Runner are the same truck. Surf is the Japanese name and 4Runner the export one. A Japanese import Surf and a New Zealand new 4Runner take the same parts.The box also carries a New Zealand distributor sticker. That one reads engine mount rear, Toyota Landcruiser Hilux. It adds the rear position and names two more models that Tenacity do not. Treat the Landcruiser and Hilux fitment as unconfirmed until we check it for you.FitmentToyota Hilux Surf and 4Runner, rear position. No years or engine are printed. Send us the rego and we will confirm what it suits.Fitting Support the driveline before the mount is undone. Worth checking the others while it is apart. Torque the bolts to the factory figure. Best fitted by a qualified mechanic.
$59.00
-
Tenacity Toyota Corolla ZZE122 Manual Front Engine Mount - Tenacity 01-12922
Front engine mount for the manual Corolla ZZE122. Tenacity 01-12922, code AWSTO1261, one mount per box.New old stock. Never fitted. The bag shows its time on the shelf.Tenacity's catalogue lists AWSTO1261 for the Corolla and Corolla Altis ZZE12#, 2000 to 2007. It is the front mount for the manual gearbox, replacing Toyota part 12361-0D030. Automatic cars take 12361-0D050, which is a different mount.ZZE122 is the 1.8 litre 1ZZ-FE Corolla of that era.FitmentToyota Corolla ZZE122, 2000 to 2007, manual, front position. Send us the rego and we will check the gearbox for you.Fitting Support the engine, then take the old mount off. Check the rest of the mounts on the car too. Torque the bolts to Toyota's figure. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Hilux Manual Rear Engine Mount - Tenacity 01-12071
Rear engine mount for the manual Toyota Hilux. Tenacity 01-12071, code AWSTO1191, one mount per box.New old stock. Never fitted. The bag shows the shelf time.This is the manual gearbox version. Automatic Hilux models take a different mount. The label gives no years and no engine, and the Hilux has run for decades, so check yours.FitmentToyota Hilux, manual transmission, rear position, as printed on the label. Send us the rego and we will confirm the generation.Fitting Take the load off the mount before you undo it. Look at the front mounts while you are under there. Bolts up to the Hilux torque figure. Best fitted by a qualified mechanic.
$59.00
-
Tenacity Toyota Harrier Lexus RX300 Engine Mount Stay - Tenacity 01-12554
Engine mount stay for the Toyota Harrier and Lexus RX300. Tenacity 01-12554, code AWSTO1232, one stay per box.Never fitted. Old stock, bag aged, stay untouched.The box lists Toyota and Lexus MCU1#. That covers MCU10 and MCU15, the 3.0 litre V6 Harrier and the RX300, built from 1998 to 2003. MCU10 is two wheel drive and MCU15 the four wheel drive.A stay is the arm with a bush at each end that stops the engine rocking under load. It is not one of the main mounts that carries the engine weight.Tenacity's catalogue lists AWSTO1232 against Toyota part 12363-20040.FitmentToyota Harrier and Lexus RX300, MCU10 and MCU15, 1998 to 2003. Send us the rego and we will confirm two or four wheel drive.Fitting Look at both bushes for splitting before anything goes back together. Check the main mounts at the same time. Both bolts back to the factory torque. Best fitted by a qualified mechanic.
$79.00
-
Tenacity Toyota Estima Hybrid AHR10 2000-2005 Engine Mount Stay - 01-12537
Engine mount stay for the Toyota Estima Hybrid AHR10. Tenacity 01-12537, code AWSTO1250, one stay per box.New old stock. Never fitted. The bag is the only thing showing storage.Tenacity's catalogue puts AWSTO1250 against Toyota part 12363-28080. That entry is the Estima Hybrid with the 2AZ-FXE 2.4 engine, chassis AHR10, from 2000 to 2005.This is the short rod with a rubber bush at each end. It stops the engine rocking under load and through the changeover between petrol and electric. A worn one gives a clunk when the engine starts or stops.Hybrid only. The AHR10 is the hybrid Estima. The petrol ACR and MCR models take different mounts.FitmentToyota Estima Hybrid, AHR10, 2.4, 2000 to 2005. Send us the rego and we will confirm the chassis.Fitting Support the engine before the old stay comes off. Look over the main mounts while you are there. Bolts to the torque figure Toyota give. Best fitted by a qualified mechanic.
$79.00
-
Tenacity Toyota Corolla 2008 on Auto Front Engine Mount - Tenacity 01-12920
Front engine mount for the automatic Corolla and Corolla Altis. Tenacity 01-12920, code AWSTO1234, one mount per box.Never fitted. Old stock, aged bag, clean mount.Tenacity's catalogue lists AWSTO1234 for the Corolla 1.6 and 1.8 from 2008. It is the front mount for the automatic, replacing Toyota part 12361-0D230. The manual cars take a different one.Altis is the name Toyota use for the Corolla in parts of Asia. It is the same car we sell here as the Corolla.FitmentToyota Corolla and Corolla Altis, 1.6 and 1.8, 2008 on, automatic, front position. Send us the rego and we will check the model.Fitting Hold the engine before the bolts come out. Look at the other mounts while you have access. Bolts back up to the Toyota setting. Best fitted by a qualified mechanic.
$89.00
-
Tenacity Toyota Premio, Corona & Avensis 1.6 Front Engine Mount - 01-11878
Front engine mount for the 1.6 Toyota Premio, Corona and Avensis. Tenacity 01-11878, code AWSTO1056, one mount per box.New old stock. Never fitted. Storage age shows on the bag.Tenacity's catalogue puts AWSTO1056 against Toyota part 12361-16300. That entry covers the Corona 1.6, the Premio 1.6 and the Avensis, 1997 to 2000. Front position, automatic.Worth knowing: the label starts with E and MT. That is shorthand for engine mount, not a gearbox code. The catalogue has this one down as automatic. Check yours if the car is a manual.The Corona Premio and the Avensis of this era share the T210 platform. The mount is common to all three names.FitmentToyota Premio 1.6, Corona 1.6 and Avensis, 1997 to 2000, front position. Send us the rego and we will settle it.Fitting Hold the engine up before you undo it. Have a look at the rest of the mounts. Bolts to the figure in the manual. Best fitted by a qualified mechanic.
$89.00
You have seen 48 out of 73 products