-
POK POK CV Joint Boot, PH714-10B
CV joint boot. POK PH714-10B, sub number PH714-10BC-L, made in Taiwan. One boot in the bag.Never fitted. Old stock, the bag showing the years.The bag names no vehicle at all, and it does not say inner or outer. Measure the boot you are replacing, or send us the rego and we will try to match it.This is the rubber boot on its own. No clamps and no grease are in the bag.FitmentNothing printed on the packaging. Ask us before ordering.Fitting Clean the old grease out of the joint before the new boot goes on. Pack it with fresh CV grease. New clamps. The old ones do not go back. Best fitted by a qualified mechanic.
$35.00
-
POK Toyota Echo Corolla 2001 on CV Joint Boot - POK PH98346
CV joint boot for the Toyota Echo and Corolla, 2001 on. POK PH98346, sub number PH98346C-L, made in Taiwan.New old stock. Never fitted. The bag shows how long it sat.This is the rubber boot by itself. The bag holds one boot, with no clamps or grease. The label does not say inner or outer, so check the one you are replacing.FitmentToyota Echo and Corolla, 2001 on, as printed on the label. Send us the rego and we will confirm the shaft.Fitting Old grease out of the joint first. Repack it with fresh CV grease. Fit new clamps rather than reusing the originals. Best fitted by a qualified mechanic.
$39.00
-
HDK Honda Accord & Prelude 1989-1998 Outer CV Joint ABS - HDK HO-22A50
Outer CV joint for the Honda Accord, with the ABS ring. HDK part number HO-22A50, one joint to a box.Never fitted, never turned. The carton is storage aged. The joint inside is as it left the factory.This is the ABS version. The A50 on the end of the number means it carries a 50 tooth ABS ring. HDK also make a plain HO-22 without the ring. If your car has ABS sensors at the front hubs, this is the one to use.Specification Inner spline, on the driveshaft: 32 teeth. Outer spline, into the hub: 28 teeth. Seal diameter: 60mm. ABS ring: 50 teeth. Count the splines on your old joint. That is the surest way to match a CV joint.Other numbers for the same joint are Febest 0310-022A50, ASVA HN-22A50 and Lynx CO-3402A.FitmentHonda Accord CB series, 1989 to 1993, including the CB1 1.8, CB3 2.0 and CB7 2.2. Also the CC, CD and CE Accord, 1993 to 1998. It is listed for the Ascot, the Inspire and the Prelude from 1991 too. Front outer, left or right. Send us your rego and we will confirm.Fitting Fit a new boot and clamps with the new joint. Pack the joint with fresh CV grease. Check the ABS ring is clean and the sensor sits at the right gap. Torque the hub nut to the factory figure and stake it. Best fitted by a qualified mechanic.
$79.00
-
HDK Mitsubishi Galant Legnum 2.5 V6 4WD Outer CV Joint - HDK MI-034A43
Outer CV joint for the 4WD Galant and Legnum V6. HDK MI-034A43, made in Japan, one joint to a box.Shrink wrap still on it. Never fitted. The carton underneath shows its age.The label gives A=32, B=54, C=25, D=66. Size catalogues read that as 32 teeth inside, a 54 mm seal and 25 outer spline teeth. The A43 means a 43 tooth ABS ring.MI-034A43 is listed for the Galant EC5A and Legnum EC5W. That is the 2.5 V6 6A13 with four wheel drive, from 1996.4WD only. The front wheel drive Galant and Legnum take a different joint. Count the splines and check the ring. Or send the rego and we will look.FitmentMitsubishi Galant EC5A and Legnum EC5W, 2.5 V6 6A13, 4WD, 1996 on, front outer. Send your rego through for confirmation.Fitting Clean splines, new circlip in place. Pack with CV grease, fit the boot, pull the clamps up. On a 4WD, do the nut up with the weight on the wheels. Check the ABS light, then drive it on full lock. Best fitted by a qualified mechanic.
$129.90
-
HDK Mazda 323, Ford Laser Outer CV Joint with ABS Ring - HDK MA-008A44
ABS outer CV joint for the Mazda 323 and Ford Laser. HDK MA-008A44, made in Japan, one joint to a box.Still in its shrink wrap and never fitted. The carton has aged underneath it.Sizes off the label: A=21, B=56, C=26, D=70. In plain words, 21 teeth inside, a 56 mm seal, 26 outer spline teeth. The A44 is a 44 tooth ABS ring.That spline and seal size matches the outer joint on the Mazda 323 BG era cars. The Ford Laser of the same era shares that base. This is the version with the ring.Count the teeth. Mazda fitted several outer joints to these cars. Check the spline count on yours and look for an ABS ring before you order. Or send us the plate and we will look it up.FitmentMazda 323 and Ford Laser with ABS, matched by spline and seal size. Send the rego and we will confirm the fit.Fitting Wipe the shaft splines down and use the new circlip. Grease the joint, then the boot and clamps. Axle nut to the factory figure, then stake or pin it. Check the ABS light before it goes on the road, and use full lock both ways. Best fitted by a qualified mechanic.
$129.90
-
HDK Mazda Astina, Eunos 1989 on Outer CV Joint with ABS - HDK MA-026A44
Outer CV joint for the Mazda Astina and Eunos, ABS version. HDK MA-026A44, made in Japan.One joint, still shrink wrapped, never on a car. The box shows its years.The label gives A=30, B=56, C=26, D=75.0. That is 30 teeth inside, a 56 mm seal and 26 outer spline teeth. The A44 stands for a 44 tooth ABS ring.The supplier label on the box puts it on the Astina and Eunos from 1989, with ABS.Worth counting first. There is more than one outer joint across these cars. Count the splines on the one coming off and check for the ring. Or we can check it off your rego.FitmentMazda Astina and Eunos, 1989 on, with ABS, as printed on the label. Rego to us and we will confirm it.Fitting New circlip, splines cleaned off first. Pack it with CV grease and fit a fresh boot and clamps. Axle nut to the book figure, staked or pinned. ABS light out, then a test drive on full lock. Best fitted by a qualified mechanic.
$129.90
-
HDK VW Passat B5, Audi A4 A6 Outer CV Joint with ABS - HDK VW-001A45
Outer CV joint for the four cylinder Passat and A4, with the ABS ring. HDK VW-001A45, made in Japan, one joint to a box.Never fitted. The box carries its years and the joint does not.The label gives A=30, B=53, C=33, D=77.1. So 30 teeth inside, a 53 mm seal and 33 outer spline teeth. The A45 is a 45 tooth ABS ring.That size matches the genuine VW and Audi outer joint 3B0498099 and 8D0498099. Parts catalogues list that joint for these cars: VW Passat B5 and B5.5, 1997 to 2005, four cylinder engines. Audi A4 B5, 1995 to 2001, four cylinder engines. Audi A6 C5, 1997 to 2005, 1.8 turbo. Skoda Superb, first generation. Count the splines. The V6 and some diesel versions take a larger joint with more splines. Count them on yours and check for the ABS ring. Or send the rego and we will confirm.Fitting Find out if your axle bolt is a stretch bolt before you think about reusing it. Work the grease in, then fit the boot and pull the clamps up. Torque the axle bolt to the factory figure. Give the 45 tooth ring a wipe before the hub goes back together. Best fitted by a qualified mechanic.
$99.00
-
HDK Toyota Corsa, Tercel, Corolla II Outer CV Joint ABS - HDK TO-037A48
ABS outer CV joint for the Toyota Corsa, Tercel and Corolla II. HDK TO-037A48.Old stock. Never been fitted. The box shows the years it has sat.HDK lists it at 23 teeth inside, a 56 mm seal and 26 outer spline teeth. The A48 means a 48 tooth ABS ring.It replaces the genuine Toyota outer joint 43410-16200 and 43410-16201. HDK lists it for these cars: Toyota Corolla II, Corsa and Tercel L40, 1990 to 1994. Chassis EL41 and NL40. Toyota Corolla II, Corsa and Tercel L50, 1994 to 1999. Chassis EL51 and NL50. Toyota Cynos EL44, 1991 to 1995. Two sizes here. Some of these cars take a joint with 22 teeth inside. Cars without ABS take a plain joint. Count the teeth inside yours and look for a ring. Or send the rego and we will look it up.Fitting The circlip is a one time part. Use the new one. Grease the joint, fit the boot, crimp the clamps. Axle nut up to the figure Toyota give. Watch that the ABS light clears before you road test it. Best fitted by a qualified mechanic.
$69.00
-
HDK Toyota Camry Vista, Townace Noah, Estima Outer CV Joint - HDK TO-018
Outer CV joint for the Toyota Townace Noah, Estima Emina and Camry Vista. HDK TO-018, written TO-18 in some catalogues.New old stock in its box. It has never been on a driveshaft.Inside it has 27 teeth. The seal is 56 mm and the outer spline has 26 teeth. This one has no ABS ring.It replaces the genuine Toyota outer joint 43410-28010, 43420-28010 and 43430-28021. HDK lists it for these cars: Toyota Camry and Vista SV3#, 1990 to 1994. Toyota Townace Noah and Liteace Noah CR50 and SR50. Toyota Estima Emina and Lucida CXR2#. Some of these take a ring. Toyota fitted more than one outer joint across this lot, and the ABS cars take a different one. Count the splines and look for a ring on yours. Or send us the rego.Fitting Fresh circlip every time, on splines you have cleaned. Pack the grease right into the cage before the boot goes over it. Axle nut to the torque Toyota specify. Full lock in both directions on the road test. Best fitted by a qualified mechanic.
$99.00
-
HDK Toyota Land Cruiser 70, Prado LJ78 Front Outer CV Joint - HDK TO-011
HDK front outer CV joint, part number TO-011. This is the joint that sits inside the front swivel housing on a solid front axle.New old stock, never fitted. The carton has been in storage a long time.It replaces the genuine Toyota joint 43405-60040. That joint has 27 teeth inside, 30 outer spline teeth and a 61.8 mm seal. It is about 240 mm long.HDK lists it for these Land Cruisers: Land Cruiser 70 series HZJ73 and HZJ77. Land Cruiser 70 series PZJ70 and PZJ77. Land Cruiser Prado LJ71 and LJ78. Toyota lists 43405-60040 for the 70 series from January 1990 to July 1999. That also covers the HZJ70, HZJ75, FZJ70, FZJ75 and PZJ73.Check the year before you buy. The 70 series built before 1990 takes a different joint with a smaller bell. So does the coil sprung 70 series from late 1999. Check the year of your truck against the Toyota number on the old joint. Or send us the rego and we will check the year.Fitting Replace the swivel hub seals and bearings while the axle is apart. Clean the axle splines and fit a new snap ring. Refill the swivel housing with the correct grease. Take it out on full lock both ways once the axle is back together. Best fitted by a qualified mechanic.
$109.00
-
HDK Toyota Camry Vista, Celica, Carina ED Outer CV Joint - HDK TO-012
Outer CV joint for the Toyota Camry, Vista, Celica and Carina ED. HDK TO-012, or TO-12 in some catalogues.Never fitted. Warehouse stock with an aged box and a clean joint.It has 27 teeth inside, a 56 mm seal and 26 outer spline teeth. There is no ring on this one. The ABS version is TO-012A48.It replaces the genuine Toyota outer joint 43410-33010, 43420-33010 and 43410-20240. HDK lists it for these cars: Toyota Camry and Vista V20 and V30 series, including CV20, CV30 and SV32. Toyota Celica and Carina ED with the 3S-FE engine, 1989 to 1993. ABS or not. Toyota used more than one outer joint here, and the ABS cars want the A48. Count the splines on yours and check for a ring. Or send the rego and we will sort it.Fitting New circlip. Clean the splines before it goes on. Grease in the joint and grease in the boot. Do the axle nut up to Toyota's figure. Listen on full lock afterwards. A click means something is not seated. Best fitted by a qualified mechanic.
$89.00
-
HDK Suzuki Swift Ignis, Mazda AZ-Wagon Outer CV Joint - HDK SU-017A43
ABS outer CV joint for the Suzuki Swift and Ignis. HDK SU-017A43, also written SU-17A43.Never fitted. Old stock, boxed, with shelf wear on the carton only.It has 19 teeth inside, a 49 mm seal and 23 outer spline teeth. Length is about 134 mm. A43 stands for a 43 tooth ABS ring.It replaces Suzuki outer joints 44101-80G00, 44101-80G10 and 44101-80G20. Parts catalogues list the same joint for these cars: Suzuki Swift SF413 and SF416, 1993 to 2003. Suzuki Ignis RG413, RG415, RM413 and RM415, 2000 to 2008. Suzuki Wagon R+ RC410 and RC413, 2004 to 2008. Mazda AZ-Wagon MD series, including MD11S. This is the Suzuki built twin of the Wagon R. Mazda Carol, Nissan Moco and Nissan Pino. Not all of them have a ring. Suzuki fitted more than one outer joint across these. Count the splines on yours and check for the ring. Or send the rego through to us.Fitting Fit the new circlip. The old one has already been stretched once. Grease it well and get both clamps tight. Axle nut to the Suzuki figure. Make sure the 43 tooth ring is clean, or the ABS will play up. Best fitted by a qualified mechanic.
$69.00
-
HDK Suzuki Baleno, Swift 22/25 Spline Outer CV Joint - HDK SU-006
Outer CV joint for the Suzuki Baleno and Swift. HDK SU-006, written SU-06 in some catalogues.New old stock. Boxed, never fitted, shelf aged on the outside.It has 22 teeth inside, a 49 mm seal and 25 outer spline teeth. No ring on this one.HDK lists it against the genuine Suzuki outer joint 44101-60G42, 44101-60G43 and 44101-60G44. Parts catalogues list the same size of joint for these cars: Suzuki Baleno and Esteem, first generation. Suzuki Swift hatch and sedan, the model sold here from 1989 to the early 2000s. Three sizes in this family. Some Balenos take 21 teeth inside and some Swifts take 19. Cars with ABS take a ring as well. Count the teeth on yours before you order, or send us the rego.Fitting Clean splines first, then the new circlip. Fill the joint with grease and clamp the boot at both ends. Axle nut torque comes from the manual, not from feel. Full lock on a quiet road, listening for a click. Best fitted by a qualified mechanic.
$89.00
-
HDK Mazda AZ-Wagon, Suzuki Alto 18/23 Spline Outer CV Joint - HDK SU-003
Small outer CV joint for 660 cc Suzuki built cars. HDK SU-003, also written SU-03.Never fitted. Old warehouse stock, box aged, joint clean.It has 18 teeth inside, a 44 mm seal and 23 outer spline teeth. No ABS ring.It replaces genuine Suzuki 44101-84012, 44101-84150 and 44101-84331. These are the fits we have found: Mazda AZ-Wagon CY21S, 660 cc F6A, 1994 to 1998. That comes from our supplier's records. The AZ-Wagon is the Suzuki built twin of the first Wagon R. Older Suzuki Alto and Maruti 800 models. European parts catalogues list the same Suzuki numbers for those. Size matters here. This is a small joint for old 660 cc and 800 cc cars. Later Altos and Wagon Rs take bigger ones. Count the splines and measure the seal. Or send the rego our way.Fitting Small joints cross thread easily, so take your time on the splines. CV grease in, boot and clamps on. Axle nut to the factory torque. Drive it on full lock and listen for clicking. Best fitted by a qualified mechanic.
$79.00
-
HDK Nissan Teana J32, Maxima J32 27/32 Spline Outer CV Joint - HDK NI-088
Outer CV joint for the Nissan Teana and Maxima J32. HDK NI-088, also written NI-88.Never fitted, still boxed. Storage shows on the box and not on the part.The HDK box lists the Maxima and Teana from 2008. It has 27 teeth inside, a 56 mm seal and 32 outer spline teeth. There is no ring fitted.The same size of joint replaces the genuine Nissan outer joint 39211-1AA0A and 39211-1AA3A. Parts catalogues list it for these cars: Nissan Teana J32, 2008 to 2013. Nissan Maxima J32, the Teana based Maxima. Nissan Murano Z51, 2008 to 2015. Nissan Elgrand E52, from 2010. More than one across the range. Nissan fitted several outer joints to this group. Count the teeth on the one coming off and measure the seal. Or send the rego and we will match it up.Fitting New circlip, and the splines cleaned before it goes on. Grease packed in, boot fitted, both clamps done up. Axle nut to the torque for the V6. Drive it on full lock each way once everything is back together. Best fitted by a qualified mechanic.
$99.00
-
HDK Nissan Primera P12, Avenir W11 Outer CV Joint ABS - HDK NI-076A44
ABS outer CV joint for the Nissan Primera P12 and Avenir W11. HDK NI-076A44, also written NI-76A44.Never fitted. Old stock, carton worn, joint untouched.Our supplier's records put it on the P12 1.8 from 2002. Inside there are 23 teeth, the seal is 56 mm and the outer spline has 27. The A44 is a 44 tooth ring.It replaces the genuine Nissan outer joint 39211-5V070. Parts catalogues list the same joint for these cars: Nissan Primera P12 sedan and WP12 wagon, 1.6 and 1.8. Nissan Avenir W11. Nissan Almera Tino V10. Nissan Prairie Liberty M12, Presage U30, R'nessa N30 and Serena C24. Ring and groove. Nissan used several joints this size across these cars, and they differ in the ABS ring and the circlip groove. Compare both against yours, and count the teeth. Or leave it with us and send the rego.Fitting Circlip out of the box, splines brushed clean. Grease into the joint, boot over it, clamps crimped. Axle nut to the Nissan setting for the P12. The 44 tooth ring wants to be clean before the sensor sees it. Best fitted by a qualified mechanic.
$59.00
-
HDK Nissan Primera P11 1.8 CVT Outer CV Joint ABS - HDK NI-066A44
ABS outer CV joint for the Nissan Primera P11 with the CVT. HDK NI-066A44, also written NI-66A44.New old stock. Never been on a driveshaft. The box carries the years.Our supplier's records put it on the P11 1.8 CVT, 1998 to 2001. It has 23 teeth inside, a 56 mm seal and 27 outer spline teeth. A44 on the end means a 44 tooth ABS ring.Febest lists its equivalent, 0210-066A44, for the Primera P11 and the Bluebird.Engine, gearbox and ABS. Nissan fitted more than one joint this size to the P11, and those three things decide which. Count the splines and look at the ring. Or send us the rego to match.Fitting New circlip on splines you have cleaned off. Fill the joint with grease, then get the boot clamped at both ends. Axle nut to the Nissan torque. Wipe the 44 tooth ring clean so the sensor can read it. Best fitted by a qualified mechanic.
$89.00
-
HDK Nissan AD Van Y11, Sunny B15 Outer CV Joint ABS - HDK NI-062A42
ABS outer CV joint for the Nissan AD Van, Sunny and Wingroad. HDK NI-062A42, also written NI-62A42.Never fitted. It has sat in the box long enough to show on the outside only.It has 23 teeth inside, a 55 mm seal and 25 outer spline teeth, at about 169 mm long. The A42 means a 42 tooth ABS ring.It replaces the genuine Nissan outer joint 39211-2N500 and 39211-2N560. Parts catalogues list it for these cars: Nissan AD Van Y11 2.2 diesel, 1999 to 2004, including 4WD. Nissan Sunny B15, 1998 to 2002, including the 2.2 diesel. Nissan Wingroad Y11 1.5, 1999 to 2005. Nissan Sunny B14, Presea R11 and Pulsar N15, mid 1990s. Same size, different rings. Nissan fitted several joints this size to these cars, some with another ring count and some with none. Count the splines and check the ring on yours. Or give us the rego and we will look.Fitting Splines wiped down, new circlip seated in its groove. Grease the joint and fill the boot before you clamp it. Axle nut to the Nissan figure. The 42 tooth ring has to be clean or the ABS will throw a fault. Best fitted by a qualified mechanic.
$89.00
-
HDK Nissan Presea HR11 2.0 23/25 Spline Outer CV Joint - HDK NI-055
Outer CV joint for the Nissan Presea with the SR20DE. HDK NI-055, also written NI-55.Old stock, never fitted, still in the box it came in.Our supplier's records put it on the Presea HR11 2.0, 1995 to 1997. It has 23 teeth inside, a 55 mm seal and 25 outer spline teeth, with no ABS ring.Parts catalogues list joints of this size for the Presea R11.Presea, Sunny and Pulsar overlap. Nissan used several joints this size across the three, and some carry a ring. Count the splines on yours and look for one. Or send the rego to us and we will check.Fitting Use the circlip in the box. The old one has had its day. Grease it well before the boot goes over the top. Axle nut up to the factory number. Listen on full lock. Clicking is the joint telling you something. Best fitted by a qualified mechanic.
$59.00
-
HDK Nissan Cefiro, Maxima A32 A33 Outer CV Joint - HDK NI-040
Outer CV joint for the Nissan Cefiro and Maxima A32 and A33. HDK NI-040, also written NI-40.New old stock. Boxed since new and never fitted.Size comes off the HDK box. 27 teeth inside, a 56 mm seal, 29 outer spline teeth and a 77 mm body. No ABS ring on it.Parts catalogues list joints of this size for these cars: Nissan Cefiro A32 and A33, including the A32 wagon. Nissan Maxima A32 and A33, V6 models. Three things to compare. Nissan used more than one joint of this size here. They differ in the circlip groove, the axle nut thread and the ABS ring. Check all three against your old one, or send the rego to us.Fitting New circlip, and clean the splines before it goes anywhere near them. Pack the grease in by hand, then boot and clamps. Axle nut to the torque Nissan give for the V6. Take it on full lock both directions once it is together. Best fitted by a qualified mechanic.
$59.00
-
HDK Nissan Primera P11 P12, Bluebird U14 Outer CV Joint - HDK NI-035
Outer CV joint for the Nissan Primera, Bluebird and Avenir. HDK NI-035, also written NI-35, made in Japan.Never fitted. New old stock with storage marks on the carton.Sizes off the HDK box: 25 teeth inside, a 56 mm seal, 27 outer spline teeth, 77 mm body. There is no ABS ring on it.It replaces the genuine Nissan outer joint 39211-5J000. Parts catalogues list that Nissan number for these cars: Nissan Primera P11 and WP11 wagon, 1995 to 2001. Nissan Primera P12, 2001 to 2005. Nissan Bluebird U14, 1996 to 2001. Nissan Avenir W11, 1998 to 2005. Nissan Prairie M12, Presage U30, Bassara and Serena C24. This one has no ring. Plenty of these cars were built with ABS and want a joint that carries one. Count the splines on yours and check before you order, or send the rego to us.Fitting Clean the splines off and use the circlip that came with it. Grease the joint, fit the boot, then crimp both ends. Axle nut done up to the workshop figure. Full lock both ways, listening at the wheel you worked on. Best fitted by a qualified mechanic.
$89.00
-
HDK Nissan Primera P11, Bluebird U14 Outer CV Joint - HDK NI-034
Outer CV joint for the Nissan Primera P11 and Bluebird U14. HDK NI-034, also written NI-34, made in Japan.Boxed since it left the factory and never fitted. Only the carton shows its age.Size is on the HDK box. 23 teeth inside, a 56 mm seal, 27 outer spline teeth and a 77 mm body. This one carries no ABS ring.Parts catalogues list NI-034 for the Primera and Bluebird. Its matching ABS joint, Febest 0210-034A44, is listed for: Nissan Primera P11 1.8 and 2.0, 1996 to 2001. Nissan Primera P10 2.0 4WD. Nissan Bluebird U13 and U14, 1.8 and 2.0. No ring on this one. Nissan put several joints this size on these cars, and the ABS ones need a ring. Count the teeth on yours and look for one. Or pass us the rego and we will do it.Fitting Splines cleaned back, then the circlip from the box. Grease through the cage before the boot goes anywhere near it. Axle nut back to the Nissan setting. A lap of the block on full lock tells you if it is right. Best fitted by a qualified mechanic.
$59.00
-
HDK Nissan Wingroad AD Y11, Sunny B15 Outer CV Joint ABS - HDK NI-017A42
ABS outer CV joint for the Nissan Wingroad and AD Y11. HDK NI-017A42, also written NI-17A42, made in Japan.New old stock. Never on a car. The box has done all the ageing.Sizes are printed on the HDK box. 23 teeth inside, a 55 mm seal, 25 outer spline teeth, a 68 mm body and about 169 mm long. A42 means a 42 tooth ABS ring.Febest lists its equivalent, 0210-017A42, against HDK NI-17A42 for these cars: Nissan Wingroad and AD Y11, 1999 to 2005. Nissan Sunny B14 and B15, and Bluebird Sylphy G10. Nissan Pulsar N14, N15 and N16. Nissan Presea R10 and R11, and the older Wingroad and AD Y10. Rings vary across this lot. Some of these cars take no ring at all and some take a different count. Check yours and count the teeth. Or send the rego and let us do it.Fitting Clean splines, circlip out of the box, seated properly in the groove. Grease the cage and fill the boot before it goes together. Axle nut to the Nissan torque for a Y11. Check the 42 tooth ring is clear of muck, then road test it. Best fitted by a qualified mechanic.
$79.00
-
HDK Nissan Primera P10 1.8 25/27 Spline Outer CV Joint - HDK NI-015
Outer CV joint for the Nissan Primera P10 1.8. HDK NI-015, also written NI-15.Never fitted. Shelf stock with an aged carton and a clean joint inside.The box lists the Primera P10 1.8 from 1992. It has 25 teeth inside, a 56 mm seal, 27 outer spline teeth and a 77 mm body. No ring fitted to this one.P10s came both ways. Nissan fitted more than one outer joint to them and some carry an ABS ring. Count the splines and check for a ring on yours. Or send the rego through and we will look.Fitting Clean splines and the new circlip, every time. Grease in the cage first, then the boot and clamps. Axle nut up to the figure Nissan give. Full lock on a quiet street before it goes back to the owner. Best fitted by a qualified mechanic.
$89.00
You have seen 24 out of 42 products